26"X16"CONDENSER KIT w/ extra length hoses suitable for Gen III 6.1L and 5.7L LX engine installs into factory a/c equipped cars. Must use BPE6644 A/C Compressor Block fittings also
nderhood Condenser Kit w/ 26"L X 16"W Multi Pass Condenser (BPE6690) fitting radiator opening of 26"inches Wide or More,Universal Condenser mounting Brackets, Single Action R134 Expansion Valve (BPE6640), Clutch Cycling Switch (BPE6696),Mini Receiver Dryer and Mounting Brackets,Hose Mounting Straps, Insulation, Fasteners,Barrier Hose Kit (#6-96", #8-60", & #10-72"), More than ample selection of all Bubble Crimp Fittings including #8 45 & 90 Degree Fittings w/ Charge Ports & #10 45 & 90 Degree Fittings w/ Charge Ports for installation at compressor.
This kit is Primarily used for Original Factory A/C Equipped Vehicles Most C Bodies, 1966-Later B Bodies, 1970-1974 E Bodies, Late A Bodies and various applications installing Gen III Hemis. For Vehicles With Original Factory A/C Evaporator. Includes Basic Installation Overview Instructions.
PICTURE SHOWN NOT REPRESENTATIVE OF ALL UNDERHOOD KITS, YOURS MAY VARY ACCORDING TO APPLICATION.
NOTE:1-
2-Larger #8 Fitting Is always installed on Upper Fitting of the Condenser.
3-Smaller #6 Fitting is always installed at bottom. #6 Outlet fitting goes to Receiver Dryer .
4-Upon Installation, Always add 1/2-3/4 ounce of PAG 46 to Condenser Before Installation.
5-Condenser will be Under Nitrogen Pressure when caps are removed
6-Always fit largest condenser to opening in radiator support for maximum efficency and cooling
7-Some triming may be necessary at corners of Condenser Mounting Flanges for Fit on Some E Bodies and B Bodies.
8-Always mount Condenser as high as possible and as close as possible to radiator support opening.
nderhood Condenser Kit w/ 26"L X 16"W Multi Pass Condenser (BPE6690) fitting radiator opening of 26"inches Wide or More,Universal Condenser mounting Brackets, Single Action R134 Expansion Valve (BPE6640), Clutch Cycling Switch (BPE6696),Mini Receiver Dryer and Mounting Brackets,Hose Mounting Straps, Insulation, Fasteners,Barrier Hose Kit (#6-96", #8-60", & #10-72"), More than ample selection of all Bubble Crimp Fittings including #8 45 & 90 Degree Fittings w/ Charge Ports & #10 45 & 90 Degree Fittings w/ Charge Ports for installation at compressor.
This kit is Primarily used for Original Factory A/C Equipped Vehicles Most C Bodies, 1966-Later B Bodies, 1970-1974 E Bodies, Late A Bodies and various applications. For Vehicles With Original Factory A/C Evaporator. Includes Basic Installation Overview Instructions.
PICTURE SHOWN NOT REPRESENTATIVE OF ALL UNDERHOOD KITS, YOURS MAY VARY ACCORDING TO APPLICATION.
NOTE:1-
2-Larger #8 Fitting Is always installed on upper of condenser.
3-Smaller #6 Fitting is always installed at bottom. #6 Outlet fitting goes to Receiver Dryer .
4-Upon Installation, Always add 1/2-3/4 ounce of PAG 46 to Condenser Before Installation.
5-Condenser will be Under Nitrogen Pressure when caps are removed
6-Always fit largest condenser to opening in radiator support for maximum efficency and cooling
7-Some triming may be necessary at corners of Condenser Mounting Flanges for Fit on Some E Bodies and B Bodies.
8-Always mount Condenser as high as possible and as close as possible to radiator support opening.
